 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| HMC611LP4 / 611LP4E v00.0607 60 dB, LOGARITHMIC DETECTOR / CONTROLLER, 1 - 10000 MHz Typical Applications The HMC611LP4(E) is ideal for IF and RF applications in: * Cellular/PCS/3G * WiMAX, WiBro, WLAN, Fixed Wireless & Radar * Power Monitoring & Control Circuitry Features Wide Dynamic Range: Up to 63 dB High Accuracy: 1 dB with 54 dB Range Up to 8 GHz Supply Voltage: +5V Excellent Stability over Temperature Buffered Temperature Sensor Output Compact 4x4mm Leadless SMT Package 8 POWER DETECTORS - SMT * Receiver Signal Strength Indication (RSSI) * Automatic Gain & Power Control Functional Diagram General Description The HMC611LP4(E) Logarithmic Detector/Controller converts RF signals at its input, to a proportional DC voltage at its output. The HMC611LP4(E) employs a successive compression topology which delivers extremely high dynamic range and conversion accuracy over a wide input frequency range. As the input power is increased, successive amplifiers move into saturation one by one creating an accurate approximation of the logarithm function. The output of a series of square law detectors is summed, converted into voltage domain and buffered to drive the LOGOUT output. For detection mode, the LOGOUT pin is shorted to the VSET input, and will provide a nominal logarithmic slope of -25mV/ dB and an intercept of 12 dBm (20 dBm for 5.8 GHz). The HMC611LP4(E) can also be used in the controller mode where an external voltage is applied to the VSET pin, to create an AGC or APC feedback loop. Electrical Specifications, TA = +25C[1] Parameter Input Frequency 3 dB Dynamic Range 3 dB Dynamic Range Center 1 dB Dynamic Range Output Slope Output Intercept Temperature Sensitivity @ -10 dBm Input [2] Typ. 50 70 -30 61 -25.8 12.5 2 Typ. 100 70 -30 61 -25.8 12.6 2 Typ. 900 71 -35.5 63 -25.5 12.7 1.1 Typ. 1900 72 -37 63 -25.0 12.2 -0.8 Typ. 2200 72 -36 62 -24.9 11.9 -0.8 Typ. 3600 66 -36 60 -24.4 12.9 7 Typ. 5800 69 -24.5 61 -24.9 20.1 -3 Typ. 7000 65 -22.5 59 -26.5 20.5 -3 Typ. 7500 63 -22.5 56 -27.1 19.9 -3 Typ. 8000 62 -22 54 -27.8 17.2 0 Typ. 10000 47 -19.5 39 -28.5 15.8 -1 Units MHz dB dBm dB mV/dB dBm mdB/C [1] Detector mode measurements; LOGOUT (Pin 15) is shorted to VSET (Pin 16). [2] Measured from TA = -45C to TA = +85C 8 - 44 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC611LP4 / 611LP4E v00.0607 60 dB, LOGARITHMIC DETECTOR / CONTROLLER, 1 - 10000 MHz Electrical Specifications, (continued) Parameter LOGOUT Interface Output Voltage Range Output Rise Time/Fall Time VSET Interface Input Impedance Input Voltage Range Low Frequency Gain Open Loop Corner Frequency Power Down (EN) Interface Voltage Range for Normal Mode Voltage Range for Powerdown Mode Threshold Voltage Power Supply (Vcc1, Vcc2, Vcc3) Operating Voltage Range Supply Current in Normal Mode Supply Current in Power Down Mode [1] Vcc= Vcc1= Vcc2= Vcc3= +5V 4.5 106 1 5.5 V mA mA 0.8 x Vcc [1] 0 Vcc [1]/2 Vcc [1] 0.2 x Vcc [1] V V V VSET to LOGOUT 30 0.25 to 1.35 56 700 k V dB kHz From 0% to 90% 0 21/9 Vcc -1.0 V ns Conditions Min. Typ. Max. Units 8 POWER DETECTORS - SMT ERROR (dB) Test Conditions Parameter Vcc1 = Vcc2 = Vcc3 Input Zo - w/ 68 Term Resistor at IN+ TA Fin Condition +5V 50 +25 C 900 MHz IN- Port connected to ground through a 1000pF capacitor Component Values Used at Key Application Frequencies with Vcc = +5V Component R8 C1 C2 Frequency (MHz) 50 3900 100nF 100nF 100 3900 100nF 100nF 900 3900 1000pF 1000pF 1900 3900 1000pF 1000pF 2200 3900 1000pF 1000pF 3600 1100 1000pF 1000pF 5800 3900 1000pF 1000pF 7000 3900 1000pF 1000pF 7500 3900 1000pF 1000pF 8000 0 1000pF 1000pF 10000 0 1000pF 1000pF LOGOUT Voltage & Error vs. Input Power, Fin = 50 MHz 2.6 2.2 1.8 1.4 1 0.6 0.2 -70 -60 -50 -40 -30 -20 -10 0 10 INPUT POWER (dBm) Ideal Logout (+25C) Logout (+85C) Logout ( -45C) ERR (+25C) ERR (+85C) ERR ( -45C) LOGOUT Voltage & Error vs. Input Power, Fin = 100 MHz 3 2 1 ERROR (dB) 0 -1 -2 -3 2.6 2.2 1.8 1.4 1 0.6 0.2 -70 -60 -50 -40 -30 -20 -10 0 10 INPUT POWER (dBm) Ideal Logout (+25C) Logout (+85C) Logout ( -45C) ERR (+25C) ERR (+85C) ERR ( -45C) 3 2 1 0 -1 -2 -3 LOGOUT (V) Unless otherwise noted: Vcc1, Vcc2, Vcc3 = +5V, TA = +25C For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com LOGOUT (V) 8 - 45 HMC611LP4 / 611LP4E v00.0607 60 dB, LOGARITHMIC DETECTOR / CONTROLLER, 1 - 10000 MHz LOGOUT Voltage & Error vs. Input Power, Fin = 900 MHz 2.6 2.2 1.8 1.4 1 0.6 Ideal Logout (+25C) Logout (+85C) Logout ( -45C) ERR (+25C) ERR (+85C) ERR ( -45C) LOGOUT Voltage & Error vs. Input Power, Fin = 1900 MHz 3 2 1 ERROR (dB) 0 -1 -2 -3 2.6 2.2 1.8 1.4 1 0.6 0.2 -70 Ideal Logout (+25C) Logout (+85C) Logout ( -45C) ERR (+25C) ERR (+85C) ERR ( -45C) 3 2 1 ERROR (dB) 0 -1 -2 -3 -60 -50 -40 -30 -20 -10 0 10 LOGOUT (V) 8 POWER DETECTORS - SMT 0.2 -70 -60 -50 -40 -30 -20 -10 0 10 LOGOUT (V) INPUT POWER (dBm) INPUT POWER (dBm) LOGOUT Voltage & Error vs. Input Power, Fin = 2200 MHz 2.6 2.2 1.8 1.4 1 0.6 0.2 -70 Ideal Logout (+25C) Logout (+85C) Logout ( -45C) ERR (+25C) ERR (+85C) ERR ( -45C) LOGOUT Voltage & Error vs. Input Power, Fin = 3600 MHz 3 2 1 ERROR (dB) 0 -1 -2 -3 2.6 2.2 1.8 1.4 1 0.6 0.2 -70 Ideal Logout (+25C) Logout (+85C) Logout ( -45C) ERR (+25C) ERR (+85C) ERR ( -45C) 3 2 1 ERROR (dB) 0 -1 -2 -3 -60 -50 -40 -30 -20 -10 0 LOGOUT (V) -60 -50 -40 -30 -20 -10 0 10 INPUT POWER (dBm) LOGOUT (V) INPUT POWER (dBm) LOGOUT Voltage & Error vs. Input Power, Fin = 5800 MHz 2.6 2.2 1.8 1.4 1 0.6 0.2 -60 Ideal Logout (+25C) Logout (+85C) Logout ( -45C) ERR (+25C) ERR (+85C) ERR ( -45C) LOGOUT Voltage & Error vs. Input Power, Fin = 7000 MHz 3 2 1 ERROR (dB) 0 -1 -2 -3 2.6 2.2 1.8 1.4 1 0.6 0.2 -60 Ideal Logout (+25C) Logout (+85C) Logout ( -45C) ERR (+25C) ERR (+85C) ERR ( -45C) 3 2 1 ERROR (dB) 0 -1 -2 -3 -50 -40 -30 -20 -10 0 10 LOGOUT (V) -50 -40 -30 -20 -10 0 10 INPUT POWER (dBm) LOGOUT (V) INPUT POWER (dBm) Unless otherwise noted: Vcc1, Vcc2, Vcc3 = +5V, TA = +25C 8 - 46 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC611LP4 / 611LP4E v00.0607 60 dB, LOGARITHMIC DETECTOR / CONTROLLER, 1 - 10000 MHz LOGOUT Voltage & Error vs. Input Power, Fin = 7500 MHz 2.6 2.2 1.8 1.4 1 0.6 0.2 -60 Ideal Logout (+25C) Logout (+85C) Logout ( -45C) ERR (+25C) ERR (+85C) ERR ( -45C) LOGOUT Voltage & Error vs. Input Power, Fin = 8000 MHz 3 2 1 ERROR (dB) 0 -1 -2 -3 2.6 2.2 1.8 1.4 1 0.6 0.2 -60 Ideal Logout (+25C) Logout (+85C) Logout ( -45C) ERR (+25C) ERR (+85C) ERR ( -45C) 3 2 1 ERROR (dB) 0 -1 -2 -3 -50 -40 -30 -20 -10 0 10 INPUT POWER (dBm) LOGOUT (V) LOGOUT (V) 8 POWER DETECTORS - SMT 8 - 47 -50 -40 -30 -20 -10 0 10 INPUT POWER (dBm) LOGOUT Voltage & Error vs. Input Power, Fin = 10000 MHz 2.6 2.2 1.8 1.4 1 0.6 0.2 -50 Ideal Logout (+25C) Logout (+85C) Logout ( -45C) ERR (+25C) ERR (+85C) ERR ( -45C) 3 2 1 ERROR (dB) 0 -1 -2 -3 -40 -30 -20 -10 0 10 LOGOUT (V) INPUT POWER (dBm) LOGOUT Slope vs. Frequency -20 -22 SLOPE (mV/dB) -24 -26 -28 -30 +25C +85C -45C LOGOUT Slope vs. Supply Voltage -25 SLOPE (mV/dB) -27 -29 -31 100 MHz 1900 MHz 3600 MHz 5800 MHz 8000 MHz 10000 MHz -33 -32 50 2000 4000 6000 8000 10000 4.5 5 Vcc (V) 5.5 FREQUENCY (MHz) Unless otherwise noted: Vcc1, Vcc2, Vcc3 = +5V, TA = +25C For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC611LP4 / 611LP4E v00.0607 60 dB, LOGARITHMIC DETECTOR / CONTROLLER, 1 - 10000 MHz LOGOUT Intercept vs. Frequency 24 22 INTERCEPT (dBm) 20 18 16 14 12 LOGOUT Intercept vs. Supply Voltage 24 22 INTERCEPT (dBm) 20 18 16 14 12 10 4.5 100 MHz 1900 MHz 3600 MHz 5800 MHz 8000 MHz 10000 MHz +25C +85C -45C 8 POWER DETECTORS - SMT 10 0 2000 4000 6000 8000 10000 FREQUENCY (MHz) 5 Vcc1, Vcc2, Vcc3 (V) 5.5 LOGOUT Error vs. Input Power, Normalized [2], Fin= 1900 MHz 2 RELATIVE ERROR TO 25C (dB) 1.5 1 0.5 0 -0.5 0.1 Input Impedance vs Frequency [3] 0.9 1.0 0.8 1.2 0.7 1.4 0. 2 .0 5 +85C -45C 0. 4 0 .6 1.6 S11 1.8 3. 0 -1 -1.5 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.2 1.4 1.6 1.8 2.0 3.0 4.0 5.0 -60 -50 -40 -30 -20 -10 0 10 0.1 INPUT POWER (dBm) 0.2 3.9 3.5 0. 3 6.5 2.7 5.0 LOGOUT Voltage vs. Input Power & Frequency 2.4 2.2 2 1.8 LOGOUT (V) 1.6 1.4 1.2 1 0.8 0.6 0.4 0.2 0 -70 -60 -50 -40 -30 -20 -10 0 10 50 MHz 100 MHz 900 MHz 1900 MHz 2200 MHz 3600MHz 5800MHz 6500MHz 7000MHz 7500MHz 8000MHz 10000MHz 0. 4 5 0 .6 0.7 0.8 0.9 INPUT POWER (dBm) [1] Unless otherwise noted: Vcc1, Vcc2, Vcc3 = +5V, TA = +25C [2] This data is relative to the room temperature performance of the HMC611LP4(E) [3] Reference plane at J1 connector on eval board 8 - 48 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 1.0 1.2 1.4 1 .6 1.8 2 .0 0. 3. 0 20 -2 -70 0.1 0.9 5.6 8.0 10 10 6.0 4.0 0.3 1.9 0.2 4.0 5.0 10.0 2.2 6.0 8.0 10 20 8.0 HMC611LP4 / 611LP4E v00.0607 60 dB, LOGARITHMIC DETECTOR / CONTROLLER, 1 - 10000 MHz Absolute Maximum Ratings Vcc1, Vcc2, Vcc3 EN VSET Input Voltage LOGOUT Output Current RF Input Power Junction Temperature Continuous Pdiss (T = 85C) (Derate 7.95 mW/C above 85C) Thermal Resistance (Rth) (junction to lead) Storage Temperature Operating Temperature +5.6V +5.6V +5.6V 3 mA +15 dBm 125 C 1.55 Watts 42 C/W -65 to +150 C -40 to +85 C ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS 8 POWER DETECTORS - SMT NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HMC APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN. Outline Drawing Package Information Part Number HMC611LP4 HMC611LP4E Package Body Material Low Stress Injection Molded Plastic RoHS-compliant Low Stress Injection Molded Plastic Lead Finish Sn/Pb Solder 100% matte Sn MSL Rating MSL1 MSL1 [1] Package Marking [3] H611 XXXX H611 XXXX [2] [1] Max peak reflow temperature of 235 C [2] Max peak reflow temperature of 260 C [3] 4-Digit lot number XXXX For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 8 - 49 HMC611LP4 / 611LP4E v00.0607 60 dB, LOGARITHMIC DETECTOR / CONTROLLER, 1 - 10000 MHz Pin Descriptions Pin Number 1, 6, 7, 13, 17, 18 Function N/C Description These pins are not connected internally; however, this product is specified with these pins connected to RF/DC ground. Interface Schematic 8 2 TEMP Temperature sensor output pin POWER DETECTORS - SMT 3, 4 IN+, IN- RF Input pins. Connect RF to IN+, and AC couple IN- to ground for single-ended operation. 5 EN Enable pin, connect to Vcc1, Vcc2, Vcc3 for normal operation. Applying voltage <0.2 x (Vcc1, Vcc2, Vcc3) will initiate power saving mode. 8 - 12, 19, 20, 23, 24 Vcc1, Vcc2, Vcc3 Bias supply. Connect supply voltage to these pins with appropriate filtering. 14 CLPF Loop filter capacitor for output ripple filtering. 8 - 50 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC611LP4 / 611LP4E v00.0607 60 dB, LOGARITHMIC DETECTOR / CONTROLLER, 1 - 10000 MHz Pin Descriptions (Continued) Pin Number Function Description Interface Schematic 15 LOGOUT Logarithmic output that converts the input power to a DC level in detector mode. Short this pin to VSET for detector mode. 8 16 VSET VSET input in controller mode. Short this pin to LOGOUT for detector mode. 21, 22 CPB, CPA Temperature compensation pins. Package Base GND Exposed paddle must be connected to RF and DC ground. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 8 - 51 POWER DETECTORS - SMT HMC611LP4 / 611LP4E v00.0607 60 dB, LOGARITHMIC DETECTOR / CONTROLLER, 1 - 10000 MHz Application & Evaluation PCB Schematic 8 POWER DETECTORS - SMT Notes Note 1: The HMC611LP4 & HMC611LP4E evaluation boards are pre-assembled for single-ended input, and detector/RSSI mode. Note 2: For detector mode, connect high impedance volt meter to the LOGOUT port, and make no connection to VSET. LOGOUT is shorted to VSET by R9, as required for detector mode. Note 3: For controller mode, remove R9 and install 0 ohm resistor (R11), then make appropriate connection to LOGOUT and VSET. In controller mode, the LOGOUT output can be used to drive a variable gain amplifier, or a variable attenuator, either directly or through a buffer or microcontroller. VSET should be connected to an external supply, typically between +0.6 and +1.9V. Note 4: Terminal CPB must be connected to ground for proper operation. 8 - 52 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC611LP4 / 611LP4E v00.0607 60 dB, LOGARITHMIC DETECTOR / CONTROLLER, 1 - 10000 MHz Evaluation PCB 8 POWER DETECTORS - SMT 8 - 53 List of Materials for Evaluation PCB 118154 [1] Item J1 - J3 J4 J5 - J11 C1, C2 C3, C5, C7 C4, C6, C8 C9 R1 R2 R3 R4 - R6, R9 R8 R12 U1 PCB [2] Description PC Mount SMA Connector Molex Connector Header DC Pin 1000 pF Capacitor, 0402 Pkg. 100 pF Capacitor, 0402 Pkg. 0.1F Capacitor, 0603 Pkg. 220 pF Capacitor, 0603 Pkg. 68 Resistor, 0603 Pkg. 1k Resistor, 0603 Pkg. 10k Resistor, 0603 Pkg. 0 Resistor, 0603 Pkg. 3.9K Resistor, 0603 Pkg. 0 Resistor, 0402 Pkg. HMC602LP4 / HMC602LP4E Logarithmic Detector / Controller 115400 Eval Board The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com |
Price & Availability of HMC611LP4E
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |